How to Build Tesla's Radiant Energy Receiver

Radiant energy receivers with emitters available in nature - the sky

1. Understand how radiant energy capture mechanism works

To build Tesla radiant energy receivers, we need to understand Tesla's patent for radiant energy receivers.

Patent on the receiver of radiation energy from the sky:

Two problems with the collection of radiant energy in nature

In the picture above, there are 2 collectors of radiant energy corresponding to figure 1 and figure 2.

Two problems with the collection of radiant energy in nature:

1. In the first machine, Fig. 1, states that there is a electrostatic difference in the dielectric between the earth and the sky. The energy obtained is not too much. Want more power, it has to be scaled up.
2. In the second machine, Fig. 2, is the development method for the method shown in Fig. 1. Specifically, the stimulation, resonance is based on the dielectric tension in the Ether. On a small scale, but thanks to excitation and resonance, unlimited electrical energy is generated. This is how to generate energy for flying saucers, space travel.

 Although the Tesla patent explains simply using a mechanical device to induce excitation and resonance. But this explanation reveals a method of generating unlimited energy using electronic components. That is, excitation and resonance do not use mechanical devices, but use electrical fluctuations of electronic circuits. It was Tesla who did this with its legendary car but also the truth. Because Tesla's nephew and many others act as witnesses.  See more: Nikola Tesla's Automobile

See details on patent explanation: Apparatus for the Utilization of Radiant Energy

2. Circuit diagram of the radiant energy receiver

If we understand the nature of the way to capture radiant energy in figure 2, then we can do the same as Tesla mentioned, or use electronic circuits to pull unlimited "dielectric energy" - just depend on the device to pull: resonance and excitation or "Tesla's impulse technology"

We can build thousands of electrical circuits to pull radiation energy after we understand the nature. Disclosure of dielectric energy is simple in Tesla's patent (figure 2), but shows that Tesla is a generous man.

We can create a multitude of different circuits to replace the part that does the resonance work.

Here is an electrical circuit that uses capacitors and diodes to pull energy from the sky:

The earth connection used here is a 12 mm copper pipe 3 metres long, driven into the ground and the ground around it saturated with water:

It is a very good electrical circuit for collecting radiant energy. However, it is just a hybrid between the patent in Fig. 1 and Fig. 2. To generate more electricity, it is necessary to design more capacitors and diodes.

The diodes used are germanium 1N34 or 1N34a as germanium diodes drop far less voltage than do silicon diodes and the 1N34 types are low-loss diodes, particularly suited to this application. Ceramic disc types are recommended for the 200 nF capacitors. The prototype build looked like this:

Now, consider this circuit as described, to be one modular building block which can lead to unlimited power from an aerial. I will represent the circuit shown above as a rectangle, showing the above circuit as:

The cable is connected to the aluminium plate using a brass bolt and nuts which the builder thinks may be significant, quite apart from avoiding any galvanitic connection to the circuit. The cable is then run vertically downwards to the circuit. For this arrangement a second earthing point is also used. This is a galvanised iron pipe 3 metres long, driven vertically into the ground which is saturated with water. The second earth is 2 metres away from the first earth.

This arrangement provides serious power, enough to cause injury to, or kill a careless human. With two modules, it will light an LED very brightly, driving it to 2.6 volts. If the LED is removed, then the voltage climbs to about twenty volts and is easily sufficient to charge a 12V battery or battery bank although that takes time. With twenty modules as 12V battery can be charged over night. It is estimated that with two hundred modules, the power would be sufficient to power a household although that has not yet been done. It should be borne in mind that each module is easy and cheap to make, so arranging for a stack of them where additional modules can be added at a later date for more power, is an ideal arrangement. The circuit is like this:

This circuit looks completely mad as the aerial input to the circuit appears to be directly short-circuited by the second earth connection. In spite of this, the circuit works very well when connected this way. Additional modules can be added without any known limit. Increased power can be had by either raising the aluminium plate higher above the ground, to say, 10 metres (33 feet), or by adding one or more additional aerial plates. As you have a good aerial connected through to a very good earth, there has to be the possibility of the equipment being hit by lightning, and so it is suggested that a protective spark-gap is installed between the aerial and the earth, close to the circuit, so that if high-voltage is suddenly applied to the aerial, the spark gap will fire and shunt the excess power through to the earth. Alternatively, possibly a better solution is to install a standard lightning rod system a few metres away from the aerial and a metre or two higher up, so that it forms a more attractive point for a lightning strike.

Further experimentation has shown that altering the connection point for the aerial has a significant effect on the results. If the connection is made at the mid point between the aerial plate and the earth connection, it produces a greater output:

With this arrangement a single module produces around 30 volts while the original method of connecting near the earth was giving about 26 volts with two modules. Jes Ascanius has carried out further experimentation and he states that diodes with response times under 30 milliseconds produce a greater output and he recommends the use of BYV27 diodes which have a 200-volt 25nS rating as he gets three times the output from them. He also recommends using them in Joule Thief circuits.

Dragan Kljajic has been experimenting with this circuit and has started by building many of these modules on a printed circuit board like this:

The above circuit is derived by Jes Ascanius, a Danish developer. It was later developed by some developers who prefer anonymity, they share on free energy forums.

As a result of queries, Jes stresses the following points:

1. The plate must be high off the ground.
2. The plate must be polished and insulated.
3. The wire must be single-strand solid wire.
4. There must not be any part of the wire above the circuit, which is not insulated.

With the above design, you will create a generator that harnesses 192 Watts of Radiant Energy continuously.

In essence, however, that radiant energy capture version is not "Tesla's impulse technology", meaning that the version is not entirely based on the patent in Fig. 2.

If the version shown in figure 2 is followed, high frequency electrical pulses are required in the electronic circuit. With this version, the energy generated is unlimited, with the scale of the electronic circuits small. Dr. Thomas Henry Moray is the one to do that. Moray has created a device that can pull 50,000 watts with just the potential stimulation and resonance between the earth and the sky.

Information about generator Moray:

Practical guide
✰* Revealed At Last: Ancient Invention Generates Energy-On-Demand
The design includes:

• Harnessing electricity from the Earth: Neither is Schumann Resonance, nor is it known by Electromagnetism. It's The Sea of Energy in Which the Earth Floats
• Extracted from ordinary electricity by the method called “fractionation.”
• Reverse Tesla coil - "Back to Back" mechanism
• Combination of radiant energy and negative resistance to amplify electricity 
• And many other plans for Free Energy.

Radiant energy receivers with artificial sources

Tesla's patent on how to collect radiant energy with artificial sources:

The S radiant energy source shown in the figure comes from another pulse technology

There are many ways to generate radiant energy, the most typical being the Tesla coil.

Special: On the secondary winding of Tesla coil, if the voltage is too high (over 100 million volts), and there is a wire connected to a tube as shown in the picture, on the tube will emit microscopic particles, go faster the speed of light, and no mass. This is the kind of particle that quantum physics doesn't want to talk about. Because if we understand the nature of this particle, then the whole theory of quantum physics collapses.

Circuit for radiant energy receivers with artificial sources:

You can apply the circuit diagrams as shown in the collection of radiant energy from the sky to the artificial radiant energy source.

The original application of the Tesla circuit diagram above is applied. Because the source of the artificial radiant energy is so large, the radiant energy receiver in Figure 4 acts as the energy converter and then feeds the load immediately. In Figure 3, there exists a pulsating technology, that is, excitation, but mainly to charge the capacitors. See explanation of the invention: Apparatus for the Utilization of Radiant Energy

Important Note:

• The creation of artificial radiant energy is a little-known technology. We often know the Tesla coil as a source.
• Creating an artificial radiant energy source, then using "pulse technology" to pull in more energy, is not necessarily the wise way. Because the sky and the earth already contain unlimited cassava potential for electricity, and can generate unlimited energy as described above.
• Finally, in the emitting medium that we call "Radiant energy" actually doesn't carry "electrical energy", it's just the dielectric on the coaxial circuit. See this article to understand radiant energy: Radiant Energy Definition

Related: Amplify Electricity for Free Energy